Perpustakaan judul masih dalam tahap pengembangan, admin siap menampung kritik dan saran
Analisis Pengaruh Variasi Arus GMAW Terhadap Tegangan Sisa dan Distorsi ASTM A656 dengan Metode Elemen Hingga
Chandra Firmansyah (2021) | Skripsi | -
Bagikan
Ringkasan
ASTM A656 merupakan baja HSLA (High Strength Low Alloy Steel) yang memiliki kekuatan (strength) dan ketangguhan (toughness) yang tinggi sehingga biasa digunakan sebagai material untuk konstruksi crane dan jembatan, rangka kendaraan heavy-duty, struktur off-shore, dan lain sebagainya. Dari uraian penerapan aplikasi tersebut, terlihat bahwa pekerjaannya tidak terlepas dari proses pengelasan. Sehubungan dengan hal itu, proses pengelasan memiliki masalah yang sering dialami diantaranya tegangan sisa dan distorsi. Tegangan sisa merupakan salah satu faktor yang dilihat untuk memperhitungkan adanya suatu potensi kegagalan pada suatu struktur, sedangkan distorsi dapat mengakibatkan terjadinya gangguan distribusi pembebanan pada suatu struktur. Tugas Akhir ini memiliki tujuan untuk menganalisis pengaruh variasi arus GMAW terhadap tegangan sisa dan distorsi yang terjadi pada material hasil pengelasan. Variasi arus listrik yang digunakan yaitu 100 A, 110 A, dan 120 A dengan ketebalan pelat 6 mm. Berhubungan dengan tujuan tugas akhir tersebut maka dilakukan simulasi menggunakan metode elemen hingga (finite element method) untuk mengetahui tegangan sisa dan distorsi yang terjadi pada pelat ASTM A656 setelah dilakukan pengelasan dan pendinginan dengan variasi arus listrik. Berdasarkan hasil simulasi, tegangan sisa transversal yang terbentuk memiliki nilai terendah pada penggunaan arus listrik 100 A yaitu sebesar 20,3060 Mpa, sedangkan nilai tertinggi terbentuk pada penggunaan arus listrik 120 A yaitu sebesar 25,1870 Mpa. Tegangan sisa longitudinal maksimum yang terbentuk memiliki nilai terendah pada penggunaan arus listrik 100 A yaitu sebesar 20,5560 Mpa, sedangkan nilai tertinggi terbentuk pada penggunaan arus listrik 120 A yaitu sebesar 25,3930 Mpa. Distorsi yang terbentuk memiliki nilai terendah pada penggunaan arus listrik 100 A yaitu sebesar 0,0181 mm, sedangkan nilai tertinggi terbentuk pada penggunaan arus listrik 120 A yaitu sebesar 0,0219 mm. Sehingga diketahui pengaruh variasi arus listrik GMAW terhadap tegangan sisa dan distorsi yaitu semakin besar arus listrik yang digunakan maka semakin besar juga tegangan sisa dan distorsi yang dihasilkan dari proses pengelasan pelat ASTM A656.
Ringkasan Alternatif
ASTM A656 is a High Strength Low Alloy (HSLA) steel that has a high value of strength and toughness, so it is commonly used as a material for the heavy-duty vehicle frames, off-shore structures, construction of cranes and bridge, etc. From the description of its application, it can be seen that the work cannot be separated from the welding process. In the welding process, there are problems that often occur including residual stress and distortion. The residual stress is one of the factors that is taken into account to determine the existence of a potential failure in a structure, while the distortion can cause disruption of the load distribution on a structure. This study aims to analyze the effect of GMAW current variations toward residual stress and distortion that occurs in the welded material. The variations in the electric current used are 100 A, 110 A, and 120 A with a plate thickness is 6 mm. Related to the research objectives, a simulation is carried out using the Finite Element Method (FEM) to determine the residual stress and distortion that occurs on the ASTM A656 plate after welding and cooling phase with variations in electric current. Based on the simulation results, the transverse residual stress has the lowest value is formed when using an electric current of 100 A, which is 20,3060 Mpa, while the highest value is formed when using an electric current of 120 A, which is 25,1870 Mpa. The longitudinal residual stress has the lowest value is formed when using an electric current of 100 A, which is 20,5560 Mpa, while the highest value is formed when using an electric current of 120 A, which is 25,3930 Mpa. The distortion formed has the lowest value when using an electric current of 100 A, which is 0,0181 mm, while the highest value is formed when using an electric current of 120 A, which is 0,0219 mm. So that it is known the effect of GMAW current variations on residual stress and distortion, namely the greater the electric current used, the greater the residual stress and distortion resulting from the ASTM A656 welding process.