Perpustakaan judul masih dalam tahap pengembangan, admin siap menampung kritik dan saran
Disain dan Implementasi Sistem Komunikasi Data SCADA Menggunakan Protokol Modbus Serial
Fauzan Zaphran Hafiz (2017) | Skripsi | Teknik Elektro
Bagikan
Ringkasan
Sistem komunikasi data SCADA yang telah dirancang dan direalisasikan pada tugas akhir ini merupakan simulasi sistem pembangkit listrik mikrohidro yang terdiri dari human machine interfece (HMI), front end processor (FEP), RTU turbin, dan RTU generator. Pada sistem ini, turbin akan disimulasikan oleh sebuah motor yang mendapat supply dari PLN. Kecepatan putaran motor dapat dikendalikan oleh sebuah inverter. Putaran motor ini akan mengakibatkan generator ikut berputar kemudian generator akan menghasilkan besar energi listrik berdasarkan kecepatan motor. Besaran-besaran pada RTU turbin dan RTU generator inilah yang dimonitor, dikendalikan, dan dikelola datanya oleh software. Pada tugas akhir ini dilakukan perancangan dan implementasi software aplikasi berbasis Basic Compiler AVR sebagai protokol komunikasi. Protokol yang digunakan merupakan protokol modbus dengan media komunikasi RS485. Protokol ini diaplikasikan antara RTU turbin dan RTU generator terhadap FEP. Software ini memiliki 2 fungsi pemonitoran. Pertama, memonitor parameter turbin seperti flowrate, suhu, dan kecepatan turbin. Kedua, memonitor parameter generator seperti tegangan output, arus output, arus penyeimbang, suhu, dan frekuensi. Besaran parameter akan ditampilkan pada layar LCD masing-masing RTU. Fungsi lain software yaitu pengendalian relai atau coil serta pengaturan besar nilai inverter. Pada sistem ini, pengendalian coil dan inverter berhasil dilakukan dengan penyimpangan nilai inverter sebesar 0.1% sampai 9%. Namun masih memiliki kekurangan pada sisi komunikasi. Yaitu tidak mampu berkomunikasi terhadap dua RTU secara bersamaan. Hal ini terjadi akibat RS485 pada sistem ini belum bekerja dengan baik. Kata kunci: SCADA, Pembangkit listrik mikrohidro, Protokol modbus, software, Basic Compiler AVR, RS485.
Ringkasan Alternatif
Data communication system of SCADA that has been designed and realized in this final project is a simulator system for micro hydro that consists of human machine interface (HMI), front end processor (FEP), RTU turbine, and RTU generator. In this system, the turbine will be simulated by a motor that supplied from PLN. The rotation speed of the motor can be controlled by an inverter. That activity will cause the generator rotate, and then the generator will produce electrical energy based on the speed of the motors. The data that has been generated from turbine and generator will be monitored, controlled, and managed by software. In this final project, it has already designed and implemented a software-based Basic Compiler AVR application as the communication protocol. The protocol uses Modbus protocol with RS485 as the communication device. The protocol is applied between RTU turbine and RTU generator to FEP. This software has two monitoring functions. The first one is for monitoring the turbine parameters such as flow rate, temperature, and speed of the turbine. The second one is for monitoring the generator parameters such as output voltage, output current, current balance, temperature, and frequency. The parameters are displayed on the LCD screen of each RTU. Beside that the software can control relay or coil and setting the value of the inverter. In this system, the process of controlling coil and controlling inverter successfully done with error inverter value about 0.1% until 9%. But it still has weakness in communication side. That can not communicate simultaneously between two RTU. This was happened due to the RS485 system is not working properly. Keywords: SCADA, Micro hydro, Modbus protocol, Software, Basic Compiler AVR, RS485.