Perpustakaan judul masih dalam tahap pengembangan, admin siap menampung kritik dan saran
Pengaruh Jarak Dan Bentuk Sengkang Terhadap Kuat Tekan Beton Pada Benda Uji Silinder
Akmal Taufiiqul Hakim NIM. (2017) | Skripsi | Teknik Sipil
Bagikan
Ringkasan
Beton bertulang sebagai elemen balok atau kolom harus diberi penulangan lentur (memanjang) dan penulangan geser. Penulangan lentur dipakai untuk menahan beban momen lentur yang terjadi balok atau kolom. Penulangan geser (sengkang) digunakan untuk menahan pembebanan geser (gaya melintang) yang terjadi pada balok atau kolom. Sebenarnya sengkang selain berfungsi sebagai penahan gaya geser juga dapat menahan gaya horizontal, semakin dekat jarak antar sengkang maka semakin tinggi penahan gaya horizontal dari sengkakng Penelitian ini bertujuan untuk mengetahui seberapa besar pengaruh jarak dan bentuk sengkang terhadap kuat tekan beton pada benda uji silinder. Pengujian ini dilakukan di Laboratorium Struktur dan Material Teknik Sipil Fakultas Teknik Institut Teknologi Bandung, dengan menggunakan benda uji berbentuk silinder dengan diameter 15 cm dan tinggi 30 cm. tulangan longitudinal yang digunakan adalah ɸ8 mm, dan tulangan sengkang ɸ6 mm. Hasil pengujian menunjukan bahwa kuat tekan terbesar antara bentuk sengkang lingkaran dan persegi berjarak 7,5 cm ialah bentuk sengkang lingkaran dengan kekuatan tekan rata-rata mencapai 22,32 MPa, sementara nilai selisih kuat tekan beton mencapai 1,40 MPa antara bentuk sengkang lingkaran dan persegi. Dan untuk persentase nilai peningkatan 6,677% terhadap perbedaan bentuk sengkang antara lingkaran dan persegi. Kemudian untuk perbedaan jarak sengkang persegi kuat tekan terbesar terdapat pada jarak sengkang 3,75cm dimana mencapai kekuatan tekan rata-rata 24,69 MPa. Sementara nilai persentase kenaikan terbesar terdapat pada jarak 3,75 dengan 11,5 yaitu 28,62%.
Ringkasan Alternatif
The reinforced concrete as a beam or column element shall be provided with bending reinforcement (elongated) and shear reinforcement. Bending reinforcement is used to withstand the load of bending moments that occur in beams or columns. Shear reinforcement (stirrup) is used to withstand shear loading (transverse forces) that occur on beams or columns. Actually, the stirrup in addition to functioning as a drag force barrier can also withstand the horizontal force, the closer the distance between the stirrup the higher the horizontal force bracket from the stirrup. This study aims to determine how much influence the distance and shape of the stirrup against the concrete compressive strength on the cylindrical test. This test was conducted at the Laboratory of Structures and Materials of Civil Engineering Faculty of Engineering Bandung Institute of Technology, using a cylindrical test with a diameter of 15 cm and a height of 30 cm. The longitudinal reinforcement used is ɸ8 mm, and stirrup reinforcement is ɸ6 mm. The test results showed that the largest compressive strength between the circular and square shapes of the stirrup is 7.5 cm is a circular stirrup with an average compressive strength reaches 22.32 MPa, while the value of difference of concrete compressive strength reaches 1.40 MPa between the circle and square shapes. For the percentage value increase of 6.677% to the difference in the shapes of the stirrup between the circle and square. Then, for the difference of squares stirrup distance, the largest compressive strength is in the 3.75 cm where it reaches an average compressive strength of 24.69 MPa. While the largest percentage increase is at the distance of 3.75 with 11.5 of 28.62%.