Perpustakaan judul masih dalam tahap pengembangan, admin siap menampung kritik dan saran
Perancangan dan Metode Pelaksanaan Pondasi Tangki pada Proyek Pembangkit Listrik Tenaga Diesel (PLTD) CPO Bangka Belitung
Nadiya Nur Fitriyani (2019) | Tugas Akhir | Teknik Sipil
Bagikan
Ringkasan
Pembangkit Listrik Tenaga Diesel Crude Palm Oil (PLTD CPO) merupakan pembangkit listrik yang berfungsi untuk memenuhi kebutuhan listrik dalam jumlah beban kecil seperti kebutuhan listrik pabrik atau digunakan sebagai cadangan listrik untuk keadaan darurat. Pada area PLTD CPO Bangka Belitung terdapat tangki penyimpanan bahan bakar yang memiliki dimensi besar dan kapasitas yang besar, maka tangki ini memerlukan pondasi yang aman dan mampu memikul beban yang bekerja pada tangki. Perancangan pondasi untuk tangki menggunakan pondasi dangkal karena kondisi tanah yang baik dan letak tanah kerasnya berada pada kedalaman yang tidak jauh dari permukaan tanah. Perancangan pondasi dilakukan untuk dua tipe tangki, yaitu tipe Tank 100 KL dan tipe Tank 30 KL. Dalam perancangan pondasi penulis melakukan pemodelan dengan software SAP2000 untuk mendapatkan gaya-gaya dalam, kemudian penulis menghitung daya dukung pondasi dengan menggunakan data SPT dan Sondir kemudian diambil hasil yang paling kritis. Setelah itu penulis menghitung kontrol stabilitas terhadap guling dan geser. Lalu penulis menghitung penulangan pondasi untuk tangki dan membuat gambar rencana dari hasil desain pondasi tangki. Kemudian penulis merencanakan motode pelaksanaan untuk pondasi tangki. Dari perancangan pondasi tipe Tank 100 KL didapat dimensi 6 x 6 x 0,5 m, beban ijin sebesar 2324,96 ton, nilai faktor keamanan stabilitas guling sebesar 68,316, dan nilai faktor keamanan stabilitas geser sebesar 20,380. Sedangkan dari perancangan pondasi tipe Tank 30 KL didapat dimensi 4 x 4 x 0,4 m, beban ijin sebesar 1033,32 ton, nilai faktor keamanan stabilitas guling sebesar 18,537, dan nilai faktor keamanan stabilitas geser sebesar 5,553.
Ringkasan Alternatif
Pembangkit Listrik Tenaga Diesel Crude Palm Oil (PLTD CPO) is a power plant that serves to meet the needs of electricity with small amount of loads, such as power plant for the factory or for the use as a backup power for emergencies. In the PLTD CPO Bangka Belitung area, there is a fuel storage tank with large dimensions and large capacity, therefore this tank requires a safe foundation that able to bear the loads that caused by the tank. The design of the foundation for the tank is using a shallow foundation because the soil conditions is exceptional and the location of hard soil is at a depth not far from the soil surface. The design of the foundation is designed for two types of tank, the 100 KL Tank type and 30 KL Tank. In design the foundation, the authors do the modeling with SAP2000 software to acquires the internal forces, then the authors calculate the bearing capacity of the foundation by using SPT and CPT datas, then used the most critical results data to do the further design. After that the authors calculate the stability control against bolsters and shear. Then the author calculates the requirements for reinforcement of the foundation for the tank and draws the plan from the design result of the tank foundation. The authors also plan the construction methods for the tank foundation. From the design of the foundation of 100 KL Tank type, obtained the dimensions result as follows; 6 x 6 x 0,5 m, with 2324,96 tons allowed load, the safety factor stability of bolster value is 68,316, and the safety factor stability of shear value is 20,380. While from the design of 30 KL Tank foundation, obtained the dimension result for 4 x 4 x 0,4 m, with 1033,32 ton allowed load, the safety factor stability of bolster value is 18,537, and the safety factor stability of shear value is 5,553.