Perpustakaan judul masih dalam tahap pengembangan, admin siap menampung kritik dan saran
Perancangan Low-Pressure Sootblower Tipe Long Retractable Untuk Supercritical Boiler Pada PLTU Cirebon 1X660 MW
Nayip Nurfikri (2020) | Skripsi | -
Bagikan
Ringkasan
Batubara merupakan bahan bakar fosil yang berlimpah dan murah, sehingga sering digunakan sebagai bahan bakar pembangkit listrik tenaga uap (PLTU). Meskipun begitu, penggunaan batubara sebagai bahan bakar dapat menimbulkan masalah salah satunya adalah slagging dan fouling. Masalah tersebut tidak dapat dihilangkan karena batubara memiliki kadar abu. Slagging dan fouling akan menempel pada zona perpindahan panas sehingga akan menurunkan effisiensi boiler. ketika sudah terjadi slagging dan fouling, salah satu cara untuk membersihkan-nya adalah dengan dilakukan sootbowing. Metoda ini mengalirkan fluida bertekanan untuk menghasilkan gaya jet nozzle untuk menjatuhkan slagging dan fouling yang menempel pada zona perpindahan panas boiler. Pada PLTU Cirebon, uap yang digunakan untuk sooblowing berasal dari low temperature superheater, metoda ini merupakan metoda konvensional. Dewasa ini, teknologi yang baru yang dikembangkan adalah low-pressure sootblower, dimana sootblowing menggunakan uap bertekanan rendah yang didapat dari ekstraksi turbin uap. konsep low-pressure sootblower sama dengan sootblower konvensional yaitu gaya nozzle sootblower harus lebih besar dari gaya deposit. Pada perancangan ini, uap low-pressure sootblower didapat dari ekstraksi turbin uap IP dengan tekanan 22,44 bar dan temperatur 444 oC. Gaya nozzle sootblower yang dirancang adalah 1090 N dengan diameter throat nozzle 20,32 mm dan diameter keluar nozzle 40,64 mm. Properties uap masuk nozzle yang dibutuhkan adalah 9 bar dengan temperatur 240oC. Ketika melewati nozzle, jet impack pressure keluarnya adalah 8,7 bar. Massa uap yang dibutuhkan untuk sootblowing adalah 9936 kg/jam, dimana teknologi ini dapat menghemat energi sebesar $2201,454/tahun. Kata kunci: Batubara, Fouling, Slagging, Sootblower, Sootblowing.
Ringkasan Alternatif
Coal is an abundant and inexpensive fossil fuel, so its often use as a fuel for steam power plant. However, the use of coal as fuel can cause problem, one of which is slagging and fouling. This problem cant be eliminated because the coal has ash content. Slagging and fouling will stick to the heat transfer zone so that it will reduce boiler efficiency. When slagging and fouling have occured, one way to clean it is by doing sootblowing. This method flows pressurized fluid to produce a jet nozzle force for dropping slagging and fouling attached to the boiler heat transfer zone. At steam power plant cirebon, the steam used for sootblowing comes from a low temperature superheater, this method called conventional method. Today, the newly technology developed is low pressure sootblower, where the sootblowing uses low-pressure steam obtained from the extraction of steam turbines. The concept of low-pressure sootblower is the same as conventional sootblower, namely must be produce jet nozzle force higher than deposit force. In this design, the low-pressure sootblower steam was obtained from IP turbine extraction with a pressure of 22,44 bar and temperature of 444 oC. The jet nozzle force sootbower designed is 1090 N, with a throat nozzle diameter of 20.32 mm and a nozzle exit diameter of 40.64 mm. The steam properties in the nozzle required are 9 bars with a temperature 240oC. When passing through the nozzle, the jet impack pressure is 8,7 bar. The flow rate of steam needed for the sootblowing is 9936 kg / hour, which can save energy of $ 2201.454 / year. Keywords: Coal, Fouling, Slagging, Sootblower, Sootblowing.