Perpustakaan judul masih dalam tahap pengembangan, admin siap menampung kritik dan saran
Perkuatan Joint Kolom Balok Beton Bertulang pada Gedung Thamrin Office Tower Jakarta
Kiki Setiawan (2019) | Skripsi | Teknik Sipil
Bagikan
Ringkasan
Proyek Thamrin Office Tower adalah proyek perkantoran yang terletak di Jakarta Pusat. Dalam pelaksanaan pembangunannya, metode pengecoran kolom dilakukan sampai setinggi dasar balok yang terbesar sedangkan untuk bagian joint pengecorannya dilakukan bersamaan dengan balok dan pelat. Berdasarkan metode pengecoran tersebut maka mutu joint yang dipakai adalah mutu balok dan pelat yang lebih rendah dari mutu kolom. Perencanaan struktur hubungan balok dan kolom pada rangka momen khusus harus memastikan kekuatan kolom lebih besar daripada kekuatan balok agar kegagalan struktur tidak terjadi pada kolom dan membuat struktur tidak runtuh ketika terjadi gempa. Selain itu sambungan kolom-balok harus memiliki kekuatan yang cukup agar kerusakan tidak terjadi pada sambungan tetapi terjadi pada ujung-ujung balok yang biasa disebut dengan sendi plastis. Setelah adanya perubahan mutu, sebagian kekuatan geser joint kolom-balok menjadi tidak kuat sehingga diperlukan perkuatan joint dengan metode ekspansi planar segitiga dan dengan memberikan pengaku baja pada pangkal balok/ kolom. Metode perkuatan ini dilakukan dengan konsep memindahkan kerusakan joint ke lokasi ujung balok yang tidak diberi perkuatan sehingga panjang ekspansi akibat beton maupun baja dapat dianggap sebagai joint sehingga memperbesar luas joint efektif. Perkuatan dengan kedua metode tersebut terbukti efektif untuk menambah kekuatan joint. Setelah dilakukan perkuatan, struktur gedung dianalisis ulang untuk mengetahui pengaruh perkuatan tersebut pada perilaku gedung secara keseluruhan. Analisis ulang struktur gedung menghasilkan perbedaan perilaku yang kecil sehingga perkuatan tersebut dapat diaplikasikan. Jika dilihat berdasarkan faktor ekonomis, perkuatan dengan beton lebih efektif untuk diimplementasikan. Kata Kunci: Metode Pengecoran, Perubahan Mutu, Kolom, Joint, Perkuatan Joint.
Ringkasan Alternatif
Thamrin Office Tower's Project is an office project located in Central Jakarta. In the construction, the column casting method is carried out to the base elevation of the largest beam, while for the joint the casting is done simultaneously with beams and plates. Based on the foundry method, the quality of the joints used is the quality of the beams and plates that are lower than the quality of the column. Planning the beam and column link structures on a special moment frame should ensure the column strength is greater than the strength of the beam so that structural failure does not occur in the column and makes the structure not collapse during an earthquake. In addition, the joint of column-beam must have sufficient strength to avoid damage to the joints but occurs at the ends of the beam commonly referred to as the plastic joint. After the change of quality, part of the column-beam joint become not strong, so it needs a joint retrofit with a triangular planar expansion method and by providing steel stiffener at the base of the beam/ column. This retrofit method is carried out by the concept of transferring joint damage to a non-retrofit beam end location so that the length of expansion due to concrete and steel can be considered as a joint thus increasing the effective joint area. Retrofitting with both methods proved to be effective for increasing joint strength. After retrofit, the structure of the building was re-analyzed to determine the effect of such retrofit on overall building behavior. Re-analysis of building structures results in small behavioral differences so that they can be applied. If viewed based on economic factors, strengthening with concrete is more effective to be implemented. Keywords: Foundry Method, Quality Change, Column, Joint, Joint Strengthening.