Perpustakaan judul masih dalam tahap pengembangan, admin siap menampung kritik dan saran
Regenerasi Pelumas Bekas Menggunakan Proses Ekstraksi Pelarut Biner (N-Heksana Dan Aseton)
Rita Inayah (2017) | Skripsi | -
Bagikan
Ringkasan
Pelumas bekas merupakan jenis limbah B3 (bahan berbahaya dan beracun), sehingga dalam pengelolaannya tidak boleh langsung dibuang ke lingkungan. Pemanfaatan pelumas bekas, dapat dilakukan dengan proses regenerasi dengan merecovery base oil dan memisahkan pengotor tersuspensi dalam pelumas bekas tersebut. Base oil yang terkandung dalam pelumas bekas dapat digunakan sebagai bahan dasar minyak pelumas. Regenerasi pelumas bekas digunakan proses ekstraksi dengan pelarut biner n-heksana dan aseton. Proses regenerasi pelumas bekas dilakukan dengan memvariasikan perbandingan volume pelumas terhadap pelarut biner yaitu 1:3, 1:6, dan 1:9. Perbandingan volume pelarut biner n-heksana dan aseton pada setiap variasi yaitu 0%:100%, 20%:80%, 40%:60%, 60%:40%, 80%:20%, dan 100%:0%. Proses ekstraksi pelumas bekas dengan pelarut biner ini dilakukan pada suhu 56℃ selama 30 menit dengan kecepatan pengadukan 600 rpm. Metode analisis yang digunakan untuk karakterisasi sampel limbah meliputi analisa gravimetri untuk menentukan kandungan pengotor dan base oil dalam sampel pelumas bekas, specific gravity dan viskositas pada 40℃. Pengukuran specific gravity pada 40℃ dan viskositas 40℃ juga dilakukan pada base oil hasil regenerasi perbandingan volume pelumas terhadap pelarut biner terbaik. Proses ekstraksi terbaik ada pada perbandingan volume pelumas terhadap pelarut biner 1:9 dengan komposisi 80%aseton dan 20% n-heksana dengan perolehan recovery base oil 96,35%, kemurnian 81,31%, dan recovery pelarut biner 70,59%. Kata kunci: limbah minyak pelumas bekas, base oil, pengotor, pelarut biner, n-heksana, aseton.
Ringkasan Alternatif
Waste lubricating oil is a kind of hazardous waste. So, the management should definitely not be directly discharged into the environment. Utilization of waste lubricating oil, can be done with the regeneration process. Regeneration of waste lubricating oil can recover the content of base oil and separating impurities suspended in the waste lubricating oil. Base oil contained in the waste lubricating oil can be used as a base lubricating oil. Regeneration of waste lubricating oil used solvent extraction process by selecting the binary solvent form of n-hexane and acetone. The regeneration of waste lubricating oil is done by varying the ratio of the volume of waste lubricating oil to a binary solvent is 1: 3, 1: 6 and 1: 9. Ratio of the volume of each solvent binary hexane and acetone at each variation is 0%: 100%, 20%: 80%, 40%: 60%, 60%: 40%, 80%: 20%, and 100%: 0%. The extraction process of waste lubricating oils, used with binary solvent is performed at a temperature of 56℃ for 30 minutes with a stirring speed of 600 rpm. The analytical method used for the characterization of waste samples include gravimetric analysis to determine the content of impurities in the sample and base oil waste lubricating oil, specific gravity at 40℃ and viscosity at ℃. Measurement of specific gravity at 40℃ and viscosity at 40℃ oil is also performed on the regenerated base oil on the best conditions of waste lubricating oil volume ratio to binary solvent. The best ratio between waste lubricating oil volume to binary solvent 1: 9 with a composition of 80% acetone and 20% n-hexane acquisition of recovery base oil obtained 96.35%, 81.31%% purification, and binary solvent recovery 70.59%. Keywords: waste lubricating oil, base oil, impurities, binary solvent, hexane, acetone.